Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Chimney Company in Gladeview, FL
Chimney inspection in Gladeview starts with a fact most out-of-town sweep companies get wrong: this is a vent and flue town, not a fireplace town. Gladeview’s concrete-block homes along the 33147 corridor rarely have a wood-burning fireplace, so the real work is rooftop exhaust stacks, B-vent chases, and bird-nested flues on flat and low-slope roofs. Our technicians have up to 11 years of experience reading exactly these systems. Call (866) 942-9444 for a free estimate.
Why Gladeview Homes Are Different
Most of Gladeview was built between the 1950s and 1970s, in a tight grid of concrete-block and stucco single-family houses and small duplexes. Those roofs are flat or low-pitch, and the “chimney” is usually an exposed metal flue, a B-vent chase, or a soffit-mounted exhaust termination rather than a masonry stack. That changes the inspection entirely. There’s little soot to sweep and a great deal of hardware to check.
Subtropical heat and year-round humidity work on that hardware constantly. Vent caps rust, mastic seals around flat-roof penetrations dry and crack, and wind-driven rain during hurricane season finds every gap. Because fireplace use here is rare, blockages tend to come from birds, insects, and storm debris rather than creosote. When a Gladeview homeowner calls us, the story is almost always a rusted or wind-damaged vent cap, or a flue packed with nesting material after a storm. We plan inspections around that reality instead of running a fireplace checklist that doesn’t fit the house.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Our Main Gladeview Services
Two jobs come up again and again on Gladeview roofs: a sweep to clear vented flues and exhaust runs, and repair for corroded caps, rusted stacks, and leaking roof penetrations.
Chimney Sweep in Gladeview
In Gladeview, a sweep is less about scraping creosote and more about clearing what actually blocks a flue here: bird nests, insect debris, and the leaf litter that collects on a low-slope roof after a storm. We run rods and brushes through the vent run, then check the cap and the roof seal while we’re up there. Soot volume is usually light, but airflow matters just as much on a gas appliance flue as on a fireplace. If you’ve noticed a draft that’s gone weak or an exhaust smell in the house, that’s the call. Book a Chimney Sweep in Gladeview and we’ll show you what came out.

Chimney Repair in Gladeview
Repair in Gladeview is mostly metal and roof work. Rusted vent caps get replaced, corroded stacks get renewed, and aging mastic around flat-roof penetrations gets cut out and resealed before the next summer downpour pushes water into the ceiling. We use Gelco and Famco caps and venting components for these replacements, which means the fix is a proper part rather than a patch. Where a flue interior has cracked or spalled, HeatShield resurfacing restores it from the inside. When a stack has failed structurally, we explain the options plainly. See Chimney Repair in Gladeview for the full list of what we handle.

Chimney Inspection in Gladeview
Chimney inspection in Gladeview is really a vent-system inspection, and the housing stock tells you why. Mid-century concrete-block homes with flat or low-pitch roofs hide their flues inside chases and behind stucco, so problems show up as rust, water staining, or weak draft long before anyone sees a cracked flue. A proper Chimney Inspection here means getting onto the roof, opening the chase where it’s accessible, and looking at the whole run from appliance connection to cap. Our technicians have up to 11 years of experience with exactly this kind of assembly.
Chimney Flue Inspection
Signs you need it
You need a flue inspection when an exhaust smell lingers in the house, draft at the appliance has weakened, or you can see rust streaks or water staining around a rooftop stack.
What it costs in Gladeview
A flue inspection in Gladeview typically runs $125 to $275, depending on how much of the chase is accessible.
How we do it
We trace the flue from the appliance connection up through the chase to the cap, check joints and seals, and confirm the vent is clear and drafting correctly.
Level 2 Chimney Inspection
Signs you need it
A Level 2 inspection is the right call after a storm has shifted a stack or cap, after any change to the appliance or venting, or when you’re buying a Gladeview home and want the vent system documented.
What it costs in Gladeview
Expect $225 to $450 for a Level 2 inspection in Gladeview, with the upper end covering roof access and a video look inside the flue.
How we do it
We inspect every accessible part of the vent system, run a camera through the flue where the layout allows, and photograph what we find so you can see it yourself.
Chimney Fire
Signs you need it
After any chimney fire, however small it seemed, the flue needs a hands-on inspection because heat damage and cracked joints often aren’t visible from the ground.
What it costs in Gladeview
Post-fire inspection and assessment in Gladeview typically falls in the $225 to $450 range, and any repair is quoted separately in writing.
How we do it
We check the flue interior for heat damage and separation, examine the cap and roof penetration, and tell you plainly whether the vent can go back into service or needs repair first.
What Chimney Inspection Costs in Gladeview
| Item | Typical range in Gladeview |
|---|---|
| Flue inspection | $125 – $275 |
| Level 2 inspection with camera | $225 – $450 |
| Post-fire inspection and assessment | $225 – $450 |
Do I really need a chimney inspection if I don’t burn wood?
Yes. In Gladeview the vent still carries exhaust from gas appliances, and a blocked or rusted flue affects that just as much. An inspection confirms the run is clear and the cap and seals are sound. Call (866) 942-9444 for an exact quote – estimates are free.
How often should a Gladeview vent system be inspected?
Once a year is a reasonable rhythm here, and after any named storm that hits the roof. Rust, wind damage, and nesting debris build up fast in this climate. Call (866) 942-9444 for an exact quote – estimates are free.
Brands We Service in Gladeview
We work with professional-grade chimney and venting brands, including DuraFlex and Olympia Chimney liner systems, HeatShield flue resurfacing, and Gelco and Famco caps and venting components. We don’t claim parts on hand in Gladeview; materials are specified per job and the turnaround is set in your written estimate. Browse our brands for the full list.
See the difference
Before
After
Before
After
Before
AfterPricing for Chimney Company in Gladeview, FL
| Service | Typical range in Gladeview |
|---|---|
| Flue inspection | $125 – $275 |
| Level 2 inspection with camera | $225 – $450 |
| Post-fire inspection and assessment | $225 – $450 |
Price in Gladeview is driven by roof access, how much of the chase can be opened, and whether the cap and roof seal need replacement alongside the inspection. Every figure here is an estimate; the written estimate we give you before any work sets the final price.
Neighborhoods We Serve in Gladeview
We cover the residential streets across Gladeview, from the blocks near Northwest 17th Avenue to the duplex rows further east toward Northwest 27th Avenue, and everywhere in between within the 33147 ZIP. Flat and low-slope roofs are the norm throughout, so bring us a photo of the stack if you’re not sure what you’ve got up there. Fast dispatch from 7am to 7pm handles most of the community on the same run.
- Blocks near Northwest 17th Avenue
- Duplex rows toward Northwest 27th Avenue
- Side streets off Northwest 79th Street
- Homes near the Gladeview neighborhood core
Service Area – Cities Near Gladeview
Gladeview sits in unincorporated Miami-Dade, and we cover the surrounding communities on the same basis. If you’re just outside the Gladeview line, we likely still reach you, including Pinewood, FL, Brownsville, FL, Miami Shores, FL, and North Miami, FL. The housing stock and the vent systems are similar across all of them, which means the same inspection approach carries over.
Serving Gladeview, FL – Our Local Coverage Area
We serve Gladeview and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Chimney Company in Gladeview
We answer 24/7 and run fast dispatch from 7am to 7pm, Sunday through Friday. Most Gladeview calls are booked into the next open slot, and we’re closed Saturday. Call (866) 942-9444 to schedule.
Replacing a cap or resealing a roof penetration usually doesn’t require one, but structural changes to a vent may. Gladeview is unincorporated Miami-Dade, so check with the county building department before work starts.
Yes, we cover all of Gladeview within 33147 plus the neighboring communities listed above. If you’re near the edge, call (866) 942-9444 and we’ll confirm coverage before booking.
If you’re hearing an odd draft, seeing rust on a rooftop stack, or just want the vent system checked before storm season, call (866) 942-9444 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Chimney Sweep Miramar handles the vent work Gladeview homes actually need, with materials you can verify and findings you can see.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Gladeview Customers Say
"Fireplace had never drawn properly since we moved in. He found the damper was only opening halfway due to a bent linkage and fixed it in ten minutes."
- Gilbert Morales"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."
- Stephanie Thompson"Swept it, capped it, and installed a proper damper. The downdraft smell in the summer that we'd lived with for years is gone."
- Eric Tran